Removes particulates like aluminum oxide Able to be cleaned by back flushing Provides perfect cooling system bleed point Installs easily in 10 minutes Has filter bypass circuit Looks good under the hood Durable construction Installs easily in Heater Hose Heater Hose ID Product Description Coolant Filtering and inspection has never been easier. Helps keep a cooling system clean, and may very well preserve your heater. This product was developed while searching for a cause of heater failure. It was found that under peak conditions as much as psi could be recorded entering the heater.
The term convection heater or convector refers to a class of devices in which the source of heat is not directly exposed. As domestic safety and the supply from water heaters keeps temperatures relatively low, radiation is inefficient in comparison to convection.
Convection heaters also work differently to electric radiators in that they disperse heat differently. Hot water[ edit ] A hot-water radiator consists of a sealed hollow metal container filled with hot water by gravity feed, a pressure pump, or convection.
|Reduces Coolant Temperatures||Our radiators, core supports, oil coolers, recovery tanks and reservoirs are not mass produced.|
As it gives out heat, the hot water cools and sinks to the bottom of the radiator and is forced out of a pipe at the other end. Anti-hammer devices Radiator system often installed to prevent or minimize knocking in hot water radiator pipes.
Hot-water baseboard[ edit ] Traditional cast iron radiators are Radiator system longer common in new construction, replaced mostly with forced hot water baseboard style radiators.
They consist of copper pipes which have aluminium fins to increase their surface area. These conduction boiler systems use conduction to transfer heat from the water into the metal radiators or convectors.
The radiators are designed to heat the air in the room using convection to transfer heat from the radiators to the surrounding air. They do this by drawing cool air in at the bottom, warming the air as it passes over the radiator fins, and discharging the heated air at the top.
This sets up convective loops of air movement within a room.
If the register is blocked either from above or below, this air movement is prevented, and the heater will not work. Baseboard heating systems are sometimes fitted with moveable covers to allow the resident to fine-tune heating by room, much like air registers in a central air system.
Steam[ edit ] Single-pipe steam radiator Steam has the advantage of flowing through the pipes under its own pressure without the need for pumping.
For this reason, it was adopted earlier, before electric motors and pumps became available. Steam is also far easier to distribute than hot water throughout large, tall buildings like skyscrapers.
However, the higher temperatures at which steam systems operate make them inherently less efficient, as unwanted heat loss is inevitably greater.
Steam pipes and radiators are prone to producing banging sounds called steam hammer. The bang is created when some of the steam condenses into water in a horizontal section of the steam piping. Subsequently, steam picks up the water, forms a "slug" and hurls it at high velocity into a pipe fitting, creating a loud hammering noise and greatly stressing the pipe.
This condition is usually caused by a poor condensate drainage strategy and is often caused by buildings settling and the resultant pooling of condensate in pipes and radiators that no longer tilt slightly back towards the boiler.
Fan-assisted heat exchanger[ edit ] A fan-assisted radiator contains a heat exchanger fed by hot water from the heating system. A thermostatic switch energises an electric fan which blows air over the heat exchanger to circulate it in a room.
Its advantages are small relative size and even distribution of heat.Over 40 Years of Service Excellence.
City Wide Radiator is recognized as a leader in servicing Alberta for all its automotive and industrial cooling system needs. RADIATOR Caps Radiator & Reservoir Caps.
Stant pioneered the development of the pressurized ornamental radiator caps with use dating back to the early ’s. By the ’s Stant became a leading supplier of hood ornaments, producing such classics as the flying quail ornament for the first Ford Model A and ornamental caps for various .
Performance Rod & Custom in Boonville, IN manufactures quality perfomance products and specializes in aluminum radiators and muscle car accessories. This shopping feature will continue to load items.
In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. Product Description: Coolant Filtering and inspection has never been easier. Helps keep a cooling system clean, and may very well preserve your heater. RADIATOR Caps Radiator & Reservoir Caps.
Stant pioneered the development of the pressurized ornamental radiator caps with use dating back to the early ’s. By the ’s Stant became a leading supplier of hood ornaments, producing such classics as the flying quail ornament for the first Ford Model A and ornamental caps for various Lincoln, Packard, Pierce-Arrow and Cadillac models.